8 GPM 4000 PSI ALKOTA GX800EFI HOT SKID POWER WASHER
alkota slim line hot skid pressure washer 8 gpm 4000 psi
to order this unit, please call 727-562-5488 m-f 8-5 est. we ship to addresses in the usa.
current lead is 2 to 3 months on this unit
22 1/4" w x 47 1/2" l x 41 1/8 h
must tighten belts after 30 days. no warranty on belts. unloader settings, clogged nozzles and loose belts are some causes of belt failure
did you know that you lose a minimum of 300 psi every 100' of 3/8" id high pressure hose when using 8 gpm? add the hose reel, any extra fittings under pressure, the gun/wand and quick connects and you are down quite a bit of pressure.
we strongly recommend that you purchase our pl-8-to or pl-8-ta kit which has everything you need to correctly plumb this unit. we recommend switching out the 1" barb to 1.5", upsizing the non-collapsible suction hose to 1.5" id, upsizing the filter to 80 mesh 1.5", installing a 1.5" bulkhead, and upsizing to a 1/2" bypass hose to the tank using yellow ag, brass hose barb and 1/2" bulkhead. increase the jump hose to the reel to a 1/2" high pressure hose and use a 50' hose as the first length of hose on the reel. (always strip all hose from the reel when in use.) upsizing the hose id's will allow you to shoot farther, increase the cleaning units and efficiency on your pressure washer as well as move much faster when using your surface cleaner. the pl-8-to or pl-8-ta kit has everything you need to plumb the pressure washer as well as connect to a reel including the 50' high pressure hose.
upsizing your hoses will prevent back-pressure to your pump, help your valves and high pressure seals last longer, prevent your safety relief valve from spraying, supply enough water to your pump using the 'double your supply hose id in relation to your inlet port' plumbing rule of thumb and keep your pump cooler leading to less down time. double check your surface cleaner hose to ensure that it is 3/8" id instead of 1/4". always use medium threadlock on your high pressure fittings instead of teflon tape. teflon tape will end up in the pump valves or clog nozzles.
if using an chemical injector, install the injector only when in use and install it several feet downstream of the unloader to prevent back-siphoning into the unloader/pump manifold.
electronic fuel injection
18" coil with stainless steel wrapper
on board 7 gallon fuel tanks
new gx800 honda v-twin engine offer higher horsepower, quiet operation and greater fuel efficiency with a three year warranty.
yes, this unit is a key start and not pull start
includes 12 volt battery and marine battery box
racor fuel filter
sds - soft dampening system for long life of the coil (accumulator)
built on an en frame
belt driven tsf2021 general pump
pressure trapped blue spring ez start unloader: never adjust the unloader
arrives ready to use. add fuel and connect to a minimum of 200 gallons water tank or ibc tote using a 1.5" non-collapsible suction hose and the hose barb that you will need to buy individually or in the pl-8-to or pl-8-ta kit which connects the 1.5" hose to the pump manifold in one fitting instead of 3.
standard accessories included below:
gun/wand assembly with insulated grip and quick connects
50′ 1/2" id high pressure hose w/quick connects
chemical injector assembly w/quick connects
1 yellow color-coded qc spray nozzle
1 color-coded qc chemical nozzle
note: all units are completely factory assembled, tested in the usa, and delivered ready to operate
to order this unit, please call 727-562-5488 m-f 8-5 est. we ship to addresses in the usa. we stock this unit.
we recommend the whisper wash 19" classic (4345), the 24" ground force (6715), the 24" lil big guy or maybe the 28" big guy for use with this 8 gpm hot skid. some users report greater efficiency using a 4 nozzle spray bay. using a larger diameter surface cleaner will cause the user to move more slowly than if using the 19"- 24" unit.
add a high pressure ball valve (6292.s) and a live gun swivel (6290) to save steps and prevent a fight with your hose.